Tag: #beltconveyors

Working near belt conveyors: Recent deaths spur MSHA safety alert

Posted on by McCraren Compliance

Lock Out Tag Out Procedures Archives - Mine Safety Center

First published by Safety+Health an NSC publication.

Arlington, VA — Spurred by numerous fatalities related to the hazards of working near belt conveyors, the Mine Safety and Health Administration has issued a safety alert.

Published on Sept. 3, the alert states that eight fatalities involving belt conveyors have occurred in the industry since Jan. 26, 2017. Six involved miners working near a moving conveyor, and two occurred during maintenance on an idle conveyor.

“All of these fatalities could have been prevented with proper lockout/tagout and blocking against motion before working,” the alert states.

MSHA details the most recent incident, which occurred in December and remains under investigation. A miner was fatally injured after removing a splice pin from a mainline conveyor that was caught between the belt and frame of the belt tailpiece.

The agency lists multiple best practices for working safely near belt conveyors, including:

  • Identify, isolate and control stored mechanical, electrical, hydraulic and gravitational energy.
  • Effectively block the belt conveyor to prevent movement in either direction.
  • Relieve belt tension by releasing energy at the take up/belt storage system. Remember: Some tensile energy might still exist.
  • Position belt splice in an area of safe access to avoid pinch points.
  • De-energize electrical power, and lock and tag the main disconnect before beginning maintenance. Permit only the person who installed a lock and tag to remove them – and only after completing the work.
  • Never lock out start and stop controls or belt switches, as they don’t disconnect power conductors.

McCraren Compliance assists employers in protecting their workers, starting with a comprehensive Work-site Analysis, Hazard Prevention, Controls, and Safety & Health Training.

Please contact us today at 888-758-4757 to learn how we can provide mine safety training and consulting for your business.

Working in Proximity to Belt Conveyors – Safety Alert

Posted on by McCraren Compliance

Lock-Out, Tag-Out, Try-Out, and Block Against Motion Before Working.

There have been eight fatalities involving belt conveyors in the mining industry since January 26, 2017. Six involved miners working near moving conveyors, while two involved maintenance of an idle conveyor. All of these fatalities could have been prevented with proper lock-out/tag-out and blocking against motion before working. The most recent fatality, involving a miner coming in contact with a moving conveyor, is under investigation.

On December 23, 2019, a miner on a belt move crew was fatally injured while removing a splice pin from a 72-inch mainline conveyor. A belt gripper and a ratchet-style come-along failed, releasing stored energy in a tightly stretched portion of the belt, causing the belting to suddenly become taut and shift upward, pinning the miner between the belt and frame of the belt tailpiece.

Belt Conveyor safety alert for September 2020
Best Practices:

Best practices During Belt Conveyor Maintenance

Block From Motion

  • Identify, isolate, and control stored mechanical, electrical, hydraulic, and gravitational energy.
  • Effectively block the belt conveyor to prevent movement in either direction.
  • Relieve belt tension by releasing the energy at the take-up/belt storage system. Be aware that some tensile energy may remain.
  • Anchor belt clamping system to substantial belt structures. Use properly rated engineered belt clamps and come-alongs. Do not use belt grippers to restrain tensioned belts.
  • Position the clamp 90 degrees to the belt’s direction of travel, and tie off in line with the belt’s direction of travel.
  • Position belt splice where it can be safely accessed to avoid pinch points.
  • Be aware of the consequences if blocking equipment fails. Stand in safe locations.

Lock and Tag

  • De-energize electrical power, and lock and tag the main disconnect before beginning maintenance. Only the person who installed a lock and tag can remove them, and only after completing the work.
  • Never lock out using the start and stop controls (belt switches). These do not disconnect power conductors.
  • Once power has been disconnected and properly locked and tagged out, test the system to assure there is no power to the belt conveyor.

Training and Communication

  • Ensure miners are trained on safe work procedures. Develop step-by-step procedures and review them with all miners before they perform non-routine maintenance tasks such as adding or removing conveyor belt.
  • Communicate effectively. After maintenance has been completed and before removing your lock and tag, ensure everyone is clear of the belt conveyor and communicate to others that you will be restarting the belt.

McCraren Compliance offers many opportunities in safety training to help circumvent accidents. Please take a moment to visit our calendar of classes to see what we can do to help your safety measures from training to consulting.